specifications are subject to change without notice. customers should verify actual device performance in their specific applications. 3314 - 4 mm square trimming potentiometer electrical characteristics standard resistance range .......................10 ohms to 2 megohms (see standard resistance table) resistance tolerance ............?0 % std. (tighter tolerance available) end resistance.......1 % or 2 ohms max. (whichever is greater) contact resistance variation ......................................3 % or 3 ohms resolution.....................................infinite insulation resistance ................500 vdc. 100 megohms min. dielectric strength sea level.................500 vac (1 minute) adjustment angle ..................210 nom. environmental characteristics power rating (300 volts max.) 70 ?......................................0.25 watt 125 ?.........................................0 watt t emperature range ....-55 ? to +125 ? t emperature coefficient ....?00 ppm/? humidity .............................90-98 % rh, 10 cycles, 240 hours trs ? %; ir 10 megohms v ibration ......20 g trs ? %; vrs ? % shock ........100 g trs ? %; vrs ? % load life .....(@ 70 ? rated power 1000 hours) trs ? % rotational life ........................100 cycles trs ? % thermal shock ..........................5 cycles trs ? %; vrs ? % physical characteristics mechanical angle ..................240 nom. to r que ..........................180 g-cm typical stop strength ...............300 g-cm typical pushover strength (z style) .............2 kilograms (4.4 lbs.) minimum w eight ................approximately 0.01 oz. marking .................manufacturer s code, r esistance code and date code wiper...................................50 % ?0 % flammability ...........................u.l. 94v-0 standard packaging j, g and r ..................500 pcs./7 ?reel z .................................200 pcs./7 ?reel h .....................................100 pcs./tube adjustment tool ..............................h-90 6.20 (.244) 5.00 (.197) 1.30 0.10 (.051 .004) 0.80 0.10 (.031 .004) 2 plcs. 2.35 (.092) 3314r-1 5.00 (.197) 4.50 (.177) adjustment slot 2.45 long (.096) x 0.51 wide (.020) x 0.51 deep (.020) 3 1 2 6.20 (.244) 2.55 0.20 (.008) typ. 0.51 0.13 (.020 .005) typ. r 0.13 max. typ. (.005) 2.3 (.090) 1.3 (.051) 2 plcs. 5.5 (.216) 2.0 (.079) 1.3 (.051) 2 plcs. 3.2 dia. (.126) thru. 0.51 0.13 (.020 .005) typ. 3 1 2 1.0 (.040) 3 plcs. 0.8 0.1 (.031 .004) 2 plcs. 2.35 (.093) 2.3 (.091) 1.3 (.051) 2 plcs. 2.0 (.079) 2.0 (.079) 3 plcs. 3314j-1 0.20 (.008) 4.50 (.177) 4.50 (.177) 2.55 (.100) typ. adj. slot 2.45 (.096) .51 (.020) .51 (.020) wide x x deep long 4.00 (.157) 5.00 (.197) 5.00 (.197) 1.30 0.1 (.051 .004) 4.50 (.177) 3 1 2 2.55 (.100) 6.20 (.244) 5.00 (.197) 1.30 0.1 (.051 .004) 0.8 0.1 (.031 .004) 2.35 (.093) 2.3 (.091) 1.3 (.051) 5.5 (.217) 2.0 (.079) 3314g-1 0.20 (.008) 0.6 (.024) 5 max. typ. 4.50 (.177) adj. slot 2.45 (.096) .51 (.020) .51 (.020) wide x x deep long typ. typ. 2 plcs. 2 plcs. 1.3 (.051) 3 plcs. features surface mount / single turn / cermet industrial / sealed compatible with surface mount manufacturing processes compatible with popular vacuum pick-and-place equipment j-hook, gull-wing and pinned configurations side adjust available meets eia/eiaj/ipc/veci smd standard trimmer designs available through distribution product dimensions dimensions are: mm (inches) tolerances: 0.25 (.010) except where noted
3 1 2 0.20 (.008) 3314h-1 0.80 (.031) 6.30 (.248) 5.00 0.10 (.197 .004) 4.00 (.157) 4.50 (.177) 4.50 (.177) 2.55 (.100) 2.55 (.100) 2.55 (.100) typ. typ. 0.6 0.1 (.024 .004) 3 plcs. 5.00 (.197) 5.00 (.197) dia. typ. adj. slot 2.45 (.096) .51 (.020) .55 (.022) wide x x deep long outside when pins are parallel (j, g styles) tape 177.8 2.03 (7.00 .080) dia. ref. 13.0 .508 (.512 .020) dia. 1.78 .254 (.070 .010) equal spaced 3 plcs. 21.01 .789 (.000 .000) dia. 2.67 .254 (.105 .010) 59.18 2.03 (2.330 .080) 12.4 + 2.01/ -.000 (.488 + .079/-.000) reel 3.29 .10 (.130 .004) .30 max. (0.12) 5.52 0.05 (.217 .002) 1.5 + .10/ ?00 (.059 + .004-.00) dia. 4.00 .10 (.157 .004) 2.00 .05 (.079 .002) 1.75 .10 (.068 .004) 12.00 .30 (4.72 .012 5.26 .10 (.207 .004) 6.45 0.10 (.254 .004) meets eia specification 481. 1.50 + 0.30 dia. (.059 .012) 6 2 (r style) tape 177.8 2.03 (7.000 .080) 13.0 .51 (.512 .020) dia. 1.78 .25 (.070) .010) 21.01 .79 (.827 .031) 2.67 .25 (.105 .010) 59.18 2.03 (2.330 .080) 12.4 + 2.01/ -.000 (.488 + .079/ - .000) reel 2.74 .10 (.108 .004) .36 (.014) 5.52 0.5 (.217 .020) 1.5 + .10/ ?00 (.060 + .004/ - .000) 4.00 .10 (.157 .004) 2.00 .05 (.079 .020) 8.00 .20 (.315 .008) 1.75 .10 (.069 .004) 12.00 .30 (.472 .012) 5.26 .10 (.207 .004) 5.26 .10 (.207 .004) 6.45 .10 (.254 .004) meets eia specification 481. max. dia. dia. dia. (g) (j) equal spaced 3 plcs. specifications are subject to change without notice. customers should verify actual device performance in their specific applications. additional features model 3314 has been approved for use by desc on drawings 88039 (3314j) and 90027 (3314g) packaging specifications - j, g and r styles product dimensions 3314 - 4 mm square trimming potentiometer how to order 3314 j - 1 - 502 e model style standard or modified product indicator (styles j, g & h) -1 = single slot -2 = cross slot product indicator (style z only) -ga4 = single slot -1 = cross slot resistance code embossed tape designator (applicable to styles j, g, r & z only) styles j, g and r: 500 pcs. /7 ?reel (standard) style z: 200 pcs./7 ?reel (standard) 1 3 cw clockwise ccw 2 wiper shaded areas not recommended for new designs. dimensions are: mm (inches) tolerances: 0.25 (.010) except where noted
rotor positioned as shown within 22 of centerline of terminal 2 cross adjustment slot long x wide x deep rotor positioned as shown within 22 of centerline of terminal 2 1 2 3 2.41 (.095) 0.51 (0.02) 0.51 (0.02) straight adjustment slot long x wide x deep 2.41 (.095) 0.51 (0.02) 0.51 (0.02) 2.54 (0.10) 1.27 (0.50) 1.19 (0.047) 1.29 (0.051) 0.61 (.024) 3.18 (.125) 5.01 (.197) 3.32 (0.131) 0.96 (.038) 5.56 (0.219) 2.54 (0.10) 1.3 (0.051) 3.48 (.137) 2.01 (.079) 2.01 (.079) 2.01 (.079) recommended pcb layout 0.26 (.010) 0.21 (.008) 5.76 (0.227) 3.08 (0.121) 3314z-1-(rc) e (cross slot) 1 2 3 3314z-ga4-(rc) e (straight slot) reel 59.18 2.03 (2.330 .080) 2.67 .25 (.105 .010) 21.01 .79 (.827 .031) dia. 1.78 .25 (.070) .010) 13.0 .51 (.512 .020) dia. 177.8 2.03 (7.000 .080) 16.4 + 2.0/ -.00 (.646 + .079/ - .00) dia. 16.00 0.3 (.630 0.012) 1.5 + 0.1/-0.0 (0.59 +.004 /-0.0) r typ. 0.5 (.020) dia. min. dia. 1.5 (.059) 12.0 (.472) 7.5 (.295) tape 1.75 (.069) 6.0 (.236) 4.0 (.157) 2.0 (.079) 5.5 (.217) 9.1 (.358) b 5?max. max. 0.40 (.016) (z style) specifications are subject to change without notice. customers should verify actual device performance in their specific applications. packaging specifications product dimensions 3314 - 4 mm square trimming potentiometer standard resistance table popular distribution resistance values listed in boldface. special resistances available. resistance resistance (ohms) code 10 100 20 200 50 500 100 101 200 201 500 501 1,000 102 2,000 202 5,000 502 10,000 103 20,000 203 50,000 503 100,000 104 200,000 204 250,000 254 500,000 504 1,000,000 105 2,000,000 205 dimensions are: mm (inches) tolerances: 0.25 (.010) except where noted rev. 10/03
|
